# Picket fence free fall lab report answers. Lab 2 Free Fall; Picket Fence Lab report 2022-11-01

Picket fence free fall lab report answers Rating: 4,6/10 1558 reviews

A picket fence free fall lab is a common physics experiment used to measure the acceleration due to gravity, or g. In this experiment, a picket fence is dropped from a known height, and the time it takes for the fence to fall to the ground is measured using a timer or stopwatch. The acceleration due to gravity can then be calculated using the equation:

g = 2*d/t^2

where d is the distance the picket fence falls and t is the time it takes to fall.

To conduct a picket fence free fall lab, you will need the following materials:

• A picket fence (typically made of cardboard or plastic)
• A timer or stopwatch
• A measuring tape or ruler
• A flat, open area for the fence to fall

To begin the experiment, start by setting up the picket fence at a known height above the ground. This can be done by placing the fence on top of a table or other raised surface. Next, use the timer or stopwatch to measure the time it takes for the fence to fall to the ground. Be sure to start the timer as soon as the fence is released, and stop it as soon as it touches the ground.

Once you have the time measurement, use the measuring tape or ruler to determine the distance the picket fence fell. With these two pieces of data, you can now calculate the acceleration due to gravity using the equation provided above.

It is important to note that the acceleration due to gravity is not a constant value, and can vary slightly depending on factors such as altitude and the mass of the object being dropped. As such, it is recommended to repeat the experiment several times and average the results to increase the accuracy of the measurement.

In conclusion, the picket fence free fall lab is a simple and effective way to measure the acceleration due to gravity. By measuring the time it takes for an object to fall a known distance, it is possible to calculate this important physical constant using basic physics principles.

## Lab Report 2

Use the black link cable to connect the interface to the TI Graphing Calculator. As we drop "a clear plastic with evenly spaced black bars on it, called the Picket Fence" through Photogate, it will calculate the amount of time the light beam from the device being blocked and send the data to Logger Pro, which we used in Lab 1. This amount is the sum of kinetic and gravitational potential energy. Inspect your Picket Fence. The indirect voice once in a while scans as an effective extended account the exact same perception.

Next

## Lab 2 Free Fall; Picket Fence Lab report

Our average acceleration was 9. Purpose The purpose of this laboratory is to determine Premium Heat Specific heat capacity Thermodynamics physics lab report quantities. We tested acceleration due to the force of gravity acting upon the picket fence as we let it drop. A calorimeter is insulated so as to minimize any loss of energy to the surroundings. Additional equipment may be required. This is due to the fact that the fence is fighting gravity as it is thrown upward, as opposed to free falling because of the pull of gravity. To observe this relationship, the time in seconds ±0.

Next

## Picket Fence Free Fall Lab Report Answers

It can also be described as the rate of change in velocity. Dropping the picket fence from higher above would change the time, and velocity, but it wont change the acceleration. DISCUSSION The purpose of the Picket Fence Free Fall Lab was to examine the acceleration of objects as they fall to earth. When writing relating to the solutions and then your treatments for generating them, remember to make use of preceding tighten of verbs, as your studies have been implemented and you are writing about the subject. Picket Fence Freefall Lab PDF Acceleration Velocity - Scribd The entire length of the Picket Fence must be able to fall freely through the Photogate. The results of the experiment Premium Force Classical mechanics Energy Picket Fence Investigation Purpose of Experiment: The purpose of this experiment of to measure the velocity and acceleration due to gravity of a picket fence and to verify the acceleration due to gravity using the picket fence with Logger Pro and Photogate.

Next

## Picket fence physics lab report Free Essays

The entire length of the Picket Fence must be able to fall freely through the Photogate. Independent variable- time Dependent variable- the temperature of water Controlled variables- the amount of water in the calorimeter - The stop watch Premium Temperature Thermodynamics Lab Report Physics The lesson is divided into 3 labs that can be completed in any order. Your medical paper will most likely be regarded with the very important attention from your lab instructors and course instructors or via the journal which you are distributing. When the object in free fall is near the surface of the earth, the gravitational force on it is nearly constant. But, proving your current comprehension of this issue under consideration can be just as extremely important. Overall, a lab report or technological paper really needs to be regarded as a paper a single may publish in a scientific journal for publication.

Next

## Picket_Fence_Free_Fall_Lab_childhealthpolicy.vumc.org

Data and Results In order to find the results, we performed the test six times and noted the slope of each line acceleration. When the object in free fall is near the surface of the earth, the gravitational force on. With the photogates and picket fences, we can calculate the velocities at different times. Materials needed: Vernier or similar picket fences with photo-g. Even runs during which the photogate was dropped from a higher height or thrown downward runs 6 and 7 , had an average acceleration of 9.

Next

## Picket Fence Free Fall Answer Key

Therefore, the data collected was very accurate. The shape of a velocity vs. In this experiment, you will have the advantage of using a very precise timer connected to the computer and a Photogate. Option 1 Quick View Go Direct® Photogate light gate £ 160. You will drop a piece of clear plastic with evenly spaced black bars on it, called a Picket Fence.

Next

## Picket Fence Free Fall Lab Answer Key

Picket Fences Free Fall Physics Lab Free Essays Studymode The purpose of the Picket Fence Free Fall Lab was to examine the acceleration of objects as they fall to earth. The Photogate has a beam of infrared light that travels from one side to the other. The present article only concerns itself with free fall in the Newtonian domain. . No other forces can be acting; in particular, air resistance must be either absent or so small as to be ignored.

Next

## Picket Fence Free Fall childhealthpolicy.vumc.org

When the object in free fall is near the surface of the earth, the gravitational force on it is nearly constant. Put one car at the top of the ramp and let it roll down. The percent error for run 2 is -0. Connect the Photogate to DIG 1 of LabQuest and choose New from the File menu. Therefore Premium Heat Energy Thermodynamics Physic- Collisions Lab Report experiment is to explore elastic and inelastic collisions in order to study the conservation of momentum and energy. Collect an eighth data run where the Picket Fence is thrown upwards through the Photogate instead of being dropped. To avoid damaging the Picket Fence, make sure it has a soft landing surface.

Next